Ascend Pipeline Guide de l'utilisateur Page 59
- Page / 321
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Configuring IP Routing
Introduction to IP routing on the Pipeline
Pipeline User’s Guide Preliminary January 30, 1998 2-9
routing connection that comes in. In that case, it does not have a route for the
incoming source IP address, and builds a temporary route using an assumed
Class A (8), B (16), or C (24) netmask for the source IP address. If this type of
connection is with a router or a host that does not recognize the initial temporary
route (that is, one from another manufacturer), you might have to turn on RIP or
configure a static route to build a route to that network.
RIP-v2 and RIP-v1 routing
The Pipeline includes a Routing Information Protocol (RIP) version 2
implementation (RIP-v2), which includes a set of improvements to RIP-v1. You
can configure the Pipeline to send, receive, or send and receive RIP-v1 or RIP-v2
on Ethernet or any WAN interface.
Note:
RIP-v2 is a compatible upgrade to RIP-v1, but do not run RIP-v2 and
RIP-v1 on the same network in such a way that the routers receive each other’s
advertisements. RIP-v1 “guesses” subnet masks, while RIP-v2 handles them
explicitly. Running the two versions on the same network can result in RIP-v1
“guesses” overriding accurate subnet information obtained via RIP-v2.
RIP-v2 includes the following improvements to RIP-v1:
Subnet routing The biggest difference between RIP-v1 and RIP-v2 is the
inclusion of subnet mask information in RIP-v2 routes.
RIP-v1 recognized subnet information only within the subnet
and purposely did not advertise subnet masks to other routers.
There was no way to distinguish between a subnet and a host
entry, unless it was for a router directly connected to the
subnet. When a RIP-v1 router receives an IP address, it
assumes the default subnet mask.
RIP-v2 passes the netmask in parallel with the address. This
enables support not only of reliable subnet routing, but also of
variable length masks within the same network as well as
Classless Inter-domain Routing (CIDR).
If a RIP-v1 router receives a RIP-v2 update that includes
netmasks, it ignores the subnet information.
- Pipeline User’s Guide 1
- Ascend Customer Service 3
- Contents 5
- About This Guide 16
- Documentation conventions 17
- Manual set 19
- Configuring WAN Connections 20
- Link encapsulation 21
- Nailed groups 22
- How calls are initiated 23
- How calls are answered 24
- Data compression options 25
- The Answer profile 26
- Connection profiles 28
- Session options 30
- Telco options 31
- Encapsulation options 32
- MP, MPP, and MP+ connections 34
- Monitoring DBA 37
- Example MP+ configuration 38
- BACP connections 40
- Nailed MPP connections 42
- Inverse ARP for Frame Relay 49
- Configuring IP Routing 51
- Host-to-router connections 52
- Router-to-router connections 53
- Subnet mask notation 54
- RIP-v2 and RIP-v1 routing 59
- Interface-based routing 60
- Managing the routing table 64
- Static and dynamic routes 66
- Configuring static routes 66
- Configuring the default route 69
- If you are using RIP-v1 71
- Route preferences 74
- Viewing the routing table 75
- Fields in the routing table 77
- 10.8.9.10 82
- 10.2.3.1 82
- Host with ISDN 82
- Example router connection 83
- Foreign and home agents 87
- IP Address Management 90
- IP Adrs=10.2.3.1 92
- Gateway=10.0.0.17 93
- Active=Yes 93
- Dest=0.0.0.0/0 93
- Metric=1 93
- Private=Yes 93
- Enabling DNS on the Pipeline 96
- Generating UDP checksums 96
- BOOTP Relay 98
- Configuring DHCP services 100
- DHCP services 101
- Setting up a DHCP server 103
- Setting up DHCP spoofing 103
- Local DNS host address table 106
- Creating the local DNS table 108
- Editing the local DNS table 109
- Translation table size 113
- Multiple-address NAT 114
- NAT for Frame Relay 117
- Well-known ports 121
- Configuring IPX Routing 122
- Extensions to standard IPX 124
- Required settings 126
- IPX Route profiles 127
- IPX SAP filters 128
- Dial Query 129
- Watchdog spoofing 130
- Automatic SPX spoofing 130
- IPX in the Answer profile 132
- IPX SAP proxy servers 135
- Managing IPX SAP filters 142
- Applying an IPX SAP filter 144
- Ethernet 146
- About IPX bridging 156
- Enabling bridging 158
- Managing the bridge table 159
- Static bridge-table entries 160
- 10.2.3.4/24 168
- 10.2.3.75/24 168
- 10.2.3.8/24 168
- 10.2.3.100/24 168
- Introduction to filters 170
- Predefined call filters 174
- Overview of Filter profiles 175
- Defining IP filter conditions 179
- Example filters 181
- NetWare Call filter 190
- IP Call filter 195
- AppleTalk Call filter 195
- When packets are not captured 197
- Displaying packets 198
- Example 2 199
- Example 3 200
- Example 4 201
- Example 5 202
- Secure Access Firewalls 203
- Filter persistence 205
- Setting Up Pipeline Security 207
- Recommended security measures 208
- Assigning a Telnet password 211
- Pipeline Security profiles 213
- Default security level 214
- Security profile passwords 214
- Security privileges 214
- Using the Full Access profile 215
- Connection security 217
- Authentication protocols 218
- Callback security 221
- Expect callback support 222
- Using security cards 223
- Requesting PAP-TOKEN mode 225
- Requesting CACHE-TOKEN 226
- Setting system values 233
- Syslog messages 236
- Using DO commands 239
- Resetting the Pipeline 244
- Terminal server commands 246
- IpAddress: ttt.ttt.ttt.ttt 250
- Pipeline 75 Voice Features 251
- Ordering voice features 253
- Caller ID supported 256
- Using Call Waiting 256
- Using Call Hold 257
- Call conferencing 258
- EAZ Terminal ID for Germany 260
- IDSL Implementations 261
- Making voice calls over IDSL 264
- APP Server utility 265
- C:\NOVELL\LSL.COM 273
- C:\NOVELL\XXXODI.COM 273
- C:\ASCEND\APPSRVDS.EXE 273
- C:\ASCEND\ 274
- Troubleshooting 278
- General problems 279
- 100 terminal 281
- ISDN BRI interface problems 284
- Bridge/router problems 286
- Check the installation 287
- Configuration problems 288
- Upgrading system software 291
- Network Interfaces 292
- The upgrade procedure 293
- Activating a Security Profile 294
- Before you begin 296
- Glossary 304
- Broadcast packets 305
- VT-100 terminal emulation 307
Xylem COND3110 HANDHELD CONDUCTIVITY METERS Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Werkzeug Xylem COND3110 HANDHELD CONDUCTIVITY METERS.
Wir stellen 1 PDF-Handbücher Xylem COND3110 HANDHELD CONDUCTIVITY METERS zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Xylem COND3110 HANDHELD CONDUCTIVITY METERS Bedienungsanleitung (41 Seiten)
Marke: Xylem | Kategorie: Tools | Größe: 0.46 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Werkzeug Xylem
| Modelle | Dokumententyp |
|---|---|
| IOLINE TRIS COMPATIBLE pH ELECTRODES |
Bedienungsanleitung
Xylem IOLINE TRIS COMPATIBLE pH ELECTRODES Benutzerhandbuch,
2 Seiten
|
| Cond 1970i |
Bedienungsanleitung
Xylem Cond 1970i User Manual,
67 Seiten
|
| MICRO-FLOW FLOW VERIFICATION SENSORS |
Bedienungsanleitung
Xylem MICRO-FLOW FLOW VERIFICATION SENSORS User Manual,
6 Seiten
|
| BLUELINE GEL FILLED pH ELECTRODES |
Bedienungsanleitung
 
Xylem BLUELINE GEL FILLED pH ELECTRODES User Manual,
2 Seiten
|
| COND3210 HANDHELD CONDUCTIVITY METERS |
Bedienungsanleitung
Xylem COND3210 HANDHELD CONDUCTIVITY METERS User Manual,
56 Seiten
|
| A-100NV DIGITAL PERISTALTIC PUMPS |
Bedienungsanleitung
Xylem A-100NV DIGITAL PERISTALTIC PUMPS User Manual,
24 Seiten
|
| A-100NE CHEMICAL PUMPS |
Bedienungsanleitung
Xylem A-100NE CHEMICAL PUMPS User Manual,
28 Seiten
|
| C3V CHEMICAL METERING PUMPS |
Bedienungsanleitung
Xylem C3V CHEMICAL METERING PUMPS User Manual,
32 Seiten
|
| C-1500N DIAPHRAGM PUMPS |
Bedienungsanleitung
Xylem C-1500N DIAPHRAGM PUMPS User Manual,
12 Seiten
|
| C-1100V DIAPHRAGM METERING PUMPS |
Bedienungsanleitung
Xylem C-1100V DIAPHRAGM METERING PUMPS User Manual,
28 Seiten
|
| ConOx |
Bedienungsanleitung
Xylem ConOx User Manual,
24 Seiten
|
| CL200 Waterproof Total Residual Chlorine Tester |
Bedienungsanleitung
Xylem CL200 Waterproof Total Residual Chlorine Tester User Manual,
9 Seiten
|
| CL500 ONLINE CHLORINE ANALYZERS MODBUS |
Bedienungsanleitung
Xylem CL500 ONLINE CHLORINE ANALYZERS MODBUS User Manual,
14 Seiten
|
| CL500 ONLINE CHLORINE ANALYZERS |
Bedienungsanleitung
Xylem CL500 ONLINE CHLORINE ANALYZERS User Manual,
36 Seiten
|
| pH/ION 3400i ION SELECTIVE ELECTRODE ANALYZER |
Bedienungsanleitung
Xylem pH/ION 3400i ION SELECTIVE ELECTRODE ANALYZER User Manual,
83 Seiten
|
| FL700 FLUORIDE METERS |
Bedienungsanleitung
Xylem FL700 FLUORIDE METERS User Manual,
10 Seiten
|
| ISE Electrodes Nh 1100 |
Bedienungsanleitung
Xylem ISE Electrodes Nh 1100 User Manual,
1 Seiten
|
| ISE Electrodes Na |
Bedienungsanleitung
Xylem ISE Electrodes Na User Manual,
2 Seiten
|
| ISE Electrodes Pb 60 |
Bedienungsanleitung
Xylem ISE Electrodes Pb 60 Benutzerhandbuch,
24 Seiten
|
| ISE Electrodes Cu 60 |
Bedienungsanleitung
Xylem ISE Electrodes Cu 60 Benutzerhandbuch,
24 Seiten
|
© 2020, manymanuals.fr. Tous droits réservés | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels